Many world-class athletes, from all sports, have the ability to get in the right state of mind and when looking for internet the state of mind is most important. These athletes visualize breaking records, crossing the finishing line first, having the gold medal draped around their necks, hearing the roar of the crowd. You should have the same attitude in looking for internet and we make it easy for you.
Such ability is not limited to sports superstars and is easy for anyone to do. In fact, all other great achievers in life, have a crystal-clear vision of the end result of their labors. They make a commitment to get there, they are overwhelmingly positive about their efforts and they know where they are going. This is exactly what you should be doing when looking for internet. Cisco Certification: Cabling Cisco Devices
by: www.SemSim.com Unshielded Twisted Pair (UTP) is a cable that has four pairs of wires twisted inside it to eliminate electrical interference. UTP cables are connected using RJ-45 connectors that have eight connector pins. The data equipment that is used for internetworking is classified as Data Terminal Equipment (DTE e.g. router interfaces) and Data Communication Equipment (DCE e.g. A WAN connects DTEs through DCE network). UTP cables are used in many configurations and for different purposes, to form an internetwork including: Straight-through Crossover Rollover Applications of UTP include: Serial transmission Integrated Service Digital Network (ISDN) connections Console connections Modular and fixed interfaces These configurations and applications are discussed below. Straight-Through Cable A straight-through cable is the standard network cable connection and is used to connect the source and destination computers through an internetworking device. Specifically, you can use it to connect a host to a hub or switch Crossover Cable In a crossover cable, the standard RJ-45 cable between the source and destination computers is cross-connected. A crossover cable can be used to connect: Two computers Two hubs A hub to a switch A cable modem to a router Two router interfaces Rollover Cable These Cisco proprietary cables used to connect to a router or switch console port. In a rollover cable (8 pins), RJ-45 connectors are usually present at each ends and are used to connect router and computer ports. Pin 1 on one end of cable connects to Pin 8 at the other end of the cable, similarly, Pin 2 connects Pin 7, and so on. Serial Transmission All WANs use serial transmission, which can pass one bit at a time over a single channel. Cisco provides a 60-pin serial connector for one end of the cable while other end of the cable may be EIA/TIA-232, V.35, EIA/TIA-449, X.21 or others; ISDN Connections ISDN refers to a collection of standards that define a digital architecture that can carry integrated voice and data, using the public-switched network. ISDN BRI (Basic Rate Interface) is a two 64 kbps Bearer channels (2B) plus one 16 kbps Data channel (D) service. ISDN BRI terminates at the customer premise with the U interface. Console Connections A console is a type of DTE through which commands are entered into the host device. Most Cisco devices support the RJ-45 console connection. A rollover cable with an RJ-45 connector is used to connect the PC or terminal to the console port of the Cisco device. Modular and Fixed Interfaces Unlike a fixed interface router, a modular interface router allows you to add new interface cards without buying a new router. In the fixed interface series, you refer to the interfaces as: interface_type interface_number For example, the first serial interface on a Cisco 2503 router would be referred to as serial 0. Higher routers have modular interfaces that allow you to change the interfaces as and when required. Here, the interfaces are referred to as: interface_type module_number/interface_number To practice such commands you can download a free CCNA router simulator from SemSim.com and proceed to the troubleshooting 1 exercise that configures ethernet 0 interface. About The Author
SemSim.com provides training resources for Cisco certification exams: CCIE, CCNP, CCNA, CCDP, CCDA. It offers FREE learning resources to students such as study guides and router simulation labs. For more information visit: http://www.SemSim.com : Making Cisco cetification easy!
support@semsim.com
|
|
